∿
Real Test Tones
The browser generates sine-wave tones at the frequencies shown during the test using the Web Audio API.
Take a hearing frequency test in your browser and explore the approximate range of low and high frequencies you can detect with your current headphones or speakers.
Listen to a sequence of pure tones and tell the test what you can detect. The tool explores lower and higher frequencies and builds an approximate tested range from your answers.
Choose how you are listening, set your device to a comfortable low volume, then use the 1 kHz reference tone to confirm that the test is audible without being loud.
This adjusts only the tone level generated by this page. It does not measure or control the physical sound pressure level from your device.
Keep the listening volume unchanged during the test. If you are unsure whether you heard a tone, choose “I Didn't Hear It.”
The highlighted area represents the approximate range between the lowest and highest frequencies you reported hearing during this test.
The result is an approximate browser-based frequency detection test. It can be affected by your headphones or speakers, device output, volume, environment and other playback conditions. It does not diagnose hearing loss or any medical condition. If you have concerns about your hearing, consult an appropriate qualified healthcare professional.
This hearing frequency test plays a sequence of sine-wave tones at different frequencies. For each tone, you simply indicate whether you could hear it.
The test begins around the middle of the frequency spectrum and then explores lower and higher frequencies. Your answers are plotted on a logarithmic frequency scale to create an approximate picture of the range detected during the test.
Unlike a microphone analyzer, this tool does not analyze your voice or record audio. It generates sound for you to listen to, making it specifically a frequency hearing test rather than a recording or vocal analysis tool.
The browser generates sine-wave tones at the frequencies shown during the test using the Web Audio API.
The test explores both ends of the frequency spectrum rather than asking only how high you can hear.
Your answers are converted into an interactive visual map showing the approximate frequencies detected in this session.
Headphones are usually the more practical choice for an online hearing frequency range test because they reduce the influence of room acoustics and make it easier to listen in a quiet environment.
They do not make the result laboratory-grade, however. Different headphone models reproduce low and high frequencies differently, and the playback device and listening level also influence what reaches your ears.
If your headphones cannot reproduce a particular frequency effectively, the test cannot determine whether a missed tone was caused by your hearing or by the playback equipment.
The answer is best treated as a range observed under the particular conditions of the test, not as a permanent measurement of your hearing.
Frequency is measured in hertz (Hz). Lower numbers correspond to slower cycles and higher numbers to faster cycles. This test explores frequencies from the low end of the audio spectrum toward very high frequencies.
When you answer that a tone was audible, that frequency is recorded as detected. Frequencies you cannot detect help the tool estimate the boundaries of the range observed during the session.
A high frequency hearing test focuses on the upper part of the frequency spectrum. In this tool, progressively higher tones are presented and your responses are used to find the highest tested frequency you reported detecting.
Very high frequencies are particularly dependent on playback equipment. A result near the upper end of the test should therefore not be interpreted independently of the headphones, speakers and device used.
The tool reports the highest detected test frequency rather than assigning a medical or qualitative rating to it.
Ronter Audio Lab reports what happened during the browser test instead of turning the result into a diagnosis or medical assessment.
A browser-based online hearing test does not know the actual sound pressure level reaching your ears. The volume control on this page changes the digital level of the generated signal, but the final acoustic output depends on your entire playback system.
Headphone frequency response, speaker response, device output, operating-system settings and environmental noise can all influence whether a tone is detectable.
For that reason, the result is deliberately described as an approximate tested hearing range. It is useful for exploring frequency perception and comparing repeated tests under similar conditions, but it should not be interpreted as a clinical hearing measurement.
Ronter Audio Lab's sound frequency test is an informational and educational browser tool. It is not a substitute for a professional hearing evaluation.
The test does not diagnose hearing loss, hearing disorders or any other medical condition. It also cannot separate the limitations of your playback equipment from the characteristics of your hearing.
If you are concerned about your hearing, notice a meaningful change, or need an accurate hearing assessment, an appropriate qualified healthcare professional can perform testing with calibrated equipment and controlled levels.
There is no reason to increase the listening level in an attempt to hear a frequency that is difficult to detect. A missed tone is simply recorded as part of this test.
Hearing frequency is only one part of listening and musical skill. Explore other Ronter Audio Lab tools for pitch, rhythm, recording, mixing and audio analysis.
The browser generates pure tones at different frequencies. After playing each tone, you indicate whether you heard it. The tool uses those answers to show the lowest and highest test frequencies detected during the session.
Headphones are recommended because they make it easier to listen in a quiet environment, but the test can also be used with speakers. In either case, the frequency response of the playback equipment affects the result.
No. It provides an approximate result under your current playback conditions. It cannot measure the calibrated acoustic level reaching your ears or separate your hearing from the limitations of your headphones or speakers.
Yes. The upper part of the test presents progressively higher frequencies and reports the highest tested frequency that you indicated you could detect.
A missed tone can have several possible explanations in an online test. Your hearing, playback equipment, listening level and surrounding noise can all affect whether a frequency is detectable.
No. Keep the listening level comfortable and consistent. Do not increase the volume simply to make a difficult frequency audible.
No. This is not a medical diagnostic test and it does not diagnose hearing loss or any other condition. It is an informational browser-based frequency detection test.
No. This test generates tones for you to listen to. It does not require microphone access.
Different headphones, speakers, audio interfaces, computers and mobile devices can reproduce the same digital tone differently. Environmental noise and listening level can also change the result.
Yes. For a more meaningful comparison, keep the same playback device, headphones or speakers, listening level and environment whenever possible.
Explore Ronter Audio Lab for more interactive audio tools, or contact Ronter Sound for recording, production and professional audio services.
Contact Ronter Sound →